Industrial Panel
We are Specialized in Manufacturing Industrial Panel Boards
12kV VCB Panel
Compact, Sturdy with an Extensible Design. Less Maintenance & High Reliability. Draw-out VCB with Compartmentalized Design. Long Electrical And Mechanical Life. Conforms to IEC 62271-100 & 200/IEC 62271-1/ IS 13118. VCB Type Tested For E2, C2, M2 Class.
33kV VCB Panel
Compact, Sturdy with an Extensible Design. Less Maintenance & High Reliability . Draw-out VCB with Compartmentalized Design. Long Electrical and Mechanical Life. Conforms to IEC 62271-100 & 200. Compatible For Remote and SCADA Operation. Closed Door Operation with Enhanced Safety.
Ring Main Unit
Ring Main Unit is a compact unit to connect, Supply and Protect transformers on a radial or an open ring power network. minimal maintenance, high product quality with reliable operation, ease in installation, independent to environmental conditions, reduced operating cost and better personal safety.
RMG Unit
Meriton Switchgear Private Limited manufactures various modules of Indoor / Outdoor type Compact package sub- Stations from 6.6KV to 33KV and up to 2500kVA transformer capacity with HT/LT Switchgear.
Porcelain Clad Outdoor Vacuum Circuit Breakers
Porcelain Clad Vacuum Circuit Breakers (PCVCBs) are designed & manufactured for outdoor applications for switching & protection in Medium Voltage Transmission & Distribution Networks keeping in mind the tropical climate. Simple construction & less number of moving parts ensure reliable service & safety.
Bus Ducts & Rising Mains
Bus duct is used in commercial and industrial settings to conduct electricity to power cables or cable bus. Structurally, a bus duct is a sheet metal duct containing either aluminum or copper busbars (metallic strips or bars that conduct a substantial electrical current) in a grounded metal enclosure.
MV Panel
A medium voltage switchgear is a set of electrical equipment enclosed in a predominantly metal structure. This centralized set includes a variety of switches, transformers, fuses and circuit breakers. Electrical panels are used to better protect, control and separate electrical equipment from each other
MCC Panel
MCC Panel (Motor Control Center) that is a device used to control and actualize the performance of an electric motor. These MCC Panels are offered in a wide variety such as compartmentalized with ACB, MCCB, SFU, DOL, ATS, Star Delta Starters & VFD STARTERS.
PMCC Panel
Our range of Power Cum Motor Control Centre (PMCC) is used to distribute the power through the panels. It is then distributed to the different motor loads located at various parts of the factory system.
APFC Panel
APFC is an automatic power factor control panel which is used to improve the power factor, whenever required, by switching ON and OFF the required capacitor bank units automatically.
PCC Panel
Auto Main Failure Panel to restore power during power failures and are installed in between the generators and main power supply. When the main supply failure occurs, the panel disconnects the main from the load, activates the generator and shifts load to generator output
PDB Panel
Power Distribution Board is used for electrical Power Distribution. In this ACB, MCCB, SDF, MCB etc are the main equipments. This receives supply from PCC. Power Distribution Board offers Isolation and Short Circuit as basic protections. Other Protections like over current, Earth Fault, Earth Leakage etc are offered on case to case basis.
Instrumental Panel
Instrumentation Contro Panels are designed to monitor and control levels such as temperature flow, current and pressure from the field instruments that are connected to it.
LT Panel for solar power plant
LT Panel is an electrical distribution board that receives power from an solar panels and distributes the same to various electronic devices and distribution boards
One Pole
Single pole porcelain clad vacuum circuit breakers (PCVCB) are designed & manufactured for outdoor application for switching & protection in Medium Voltage Transmission & Distribution Networks keeping in mind the tropical climate.
Meter Board
Multi Meter Bus Bar Panel Pre drilled in each corner for fixings. Fire Resistant. Used for mounting electric meters and consumer units. Various sizes available
Feeder Pillar Panel (Outdoor)
A feeder pillar, also known as a power box, a distribution pillar, or a feeder pillar box, is a container that is used to- house electrical equipment's. It acts as a central course that controls and distributes electricity to outgoing circuits.
Auto/Manual Synchronizing Load Sharing Panel
Auto/Manual Synchronizing Load Sharing Panel A load sharing system will continuously adjust the engine speed settings to avoid fluctuations in the average power that is generated. The gen-sets are bundled as if they were one by synchronizing the electrical output torque. This way they will behave as if they are mechanically tied together.
Fire Panel | Fire Alarm Panel
An alarm control panel is the central hub of a security set up. All of a user's security devices will connect with the control panel to alert the user when they are activated. An alarm control panel can also be used to activate any home automation
Cable Tray & Accessories
Cable trays are mechanical support systems that provide a rigid structural system for electrical cables, raceways, and insulated conductors used for electric power distribution, control, signal instrumentation, and communication.
AMF Panel
Auto Main Failure Panel to restore power during power failures and are installed in between the generators and main power supply. When the main supply failure occurs, the panel disconnects the main from the load, activates the generator and shifts load to generator output.
Main Distribution Panel
A Main Distribution Panel (MDP) is a key component in an electrical distribution system that serves to distribute electrical power from the main source to various sub-distribution panels and loads within a building or facility.
Salient Features
- Bus bars and interlinks are insulated with heat shrinkable PVC sleeves
- Provision for future expansion for both sides
- All live parts are shrouded with polycarbonate sheets
- Customer choice of protection, metering and controlling including SCADA interface
- Single & Double Front Panel (PCC/ MCC /PMCC /MDB)
- Provision for padlocking feeder & bus bar shutters
- Ferrules Machine
- Laser Engraving Machine
- Testing Equipment’s like Megger, Insulation testing, Clamp Meter etc
- CNC Sheering and Bending Machine
- Hydraulic Busbar Cutting, Bending & punching Machine
- Well Trained Staffs with DEEE & BE(EEE) Qualification
- Design tested at CPRI for short circuit & temperature rise as per IS standards
- Worked with Architect CR Narayana Rao for TNHB Project
- 2500A Panels successfully tested at CPRI for temperature rise as per IS standards
- CNC Fabricated fully bolted standardized designs
- Computer Aided Design (CAD)systems
- Panel enclosure degree of protection IP 54, IP 55 & IP 65
- Anti-corrosion treatment and Sand Blasting Process
- Automatic spray conveyorized Pre-Treatment plant with 7 Tank Process
- Painting in dust & vermin proof paint booths & ovens
- Non hygroscopic SMC bus bar supports for best mechanical & electrical strengths for fault current withstand